* Sea-Bird SBE 9 Data File:
* FileName = C:\Data\simz2014c39.hex
* Software Version Seasave V 7.22.4
* Temperature SN = 2813
* Conductivity SN = 0492
* Number of Bytes Per Scan = 37
* Number of Voltage Words = 4
* Number of Scans Averaged by the Deck Unit = 1
* System UpLoad Time = Jul 31 2014 14:46:27
* NMEA Latitude = 38 18.65 N
* NMEA Longitude = 123 06.78 W
* NMEA UTC (Time) = Jul 31 2014  21:46:25
* Store Lat/Lon Data = Append to Every Scan
* SBE 11plus V 5.1g
* number of scans to average = 1
* pressure baud rate = 9600
* NMEA baud rate = 4800
* Latitude/Longitude added to scan
* GPIB address = 1
* advance primary conductivity  0.073 seconds
* advance secondary conductivity  0.073 seconds
* autorun on power up is disabled
* S>
** Project: SIMZ
** Platform: Rachel Carson
** Cruise: SIMZ2014
** Site: 39
** Cast Sequence: 39
** CTD ID: 91723
* System UTC = Jul 31 2014 21:46:27
# nquan = 30
# nvalues = 31                          
# units = specified
# name 0 = timeJ: Julian Days
# name 1 = prDM: Pressure, Digiquartz [db]
# name 2 = depSM: Depth [salt water, m]
# name 3 = c0S/m: Conductivity [S/m]
# name 4 = c1S/m: Conductivity, 2 [S/m]
# name 5 = t090C: Temperature [ITS-90, deg C]
# name 6 = t190C: Temperature, 2 [ITS-90, deg C]
# name 7 = potemp090C: Potential Temperature [ITS-90, deg C]
# name 8 = potemp190C: Potential Temperature, 2 [ITS-90, deg C]
# name 9 = xmiss: Beam Transmission, Chelsea/Seatech [%]
# name 10 = bat: Beam Attenuation, Chelsea/Seatech [1/m]
# name 11 = v1: Voltage 1
# name 12 = sbeox0V: Oxygen raw, SBE 43 [V]
# name 13 = v2: Voltage 2
# name 14 = flECO-AFL: Fluorescence, WET Labs ECO-AFL/FL [mg/m^3]
# name 15 = v3: Voltage 3
# name 16 = upoly0: Upoly 0, QCP-200
# name 17 = v4: Voltage 4
# name 18 = par: PAR/Irradiance, Biospherical/Licor
# name 19 = v5: Voltage 5
# name 20 = altM: Altimeter [m]
# name 21 = v6: Voltage 6
# name 22 = sal00: Salinity, Practical [PSU]
# name 23 = sal11: Salinity, Practical, 2 [PSU]
# name 24 = sigma-�00: Density [sigma-theta, Kg/m^3]
# name 25 = sigma-�11: Density, 2 [sigma-theta, Kg/m^3]
# name 26 = sbeox0ML/L: Oxygen, SBE 43 [ml/l], WS = 2
# name 27 = sbeox0PS: Oxygen, SBE 43 [% saturation], WS = 2
# name 28 = nbin: number of scans per bin
# name 29 = flag: flag
# span 0 = 212.907347, 212.909648       
# span 1 =      2.015,     32.245       
# span 2 =      2.000,     32.000       
# span 3 =   3.831394,   4.275939       
# span 4 =   3.830354,   4.275364       
# span 5 =    11.5899,    16.5270       
# span 6 =    11.5970,    16.5340       
# span 7 =    11.5859,    16.5267       
# span 8 =    11.5930,    16.5337       
# span 9 =    82.5272,    87.3215       
# span 10 =     0.5424,     0.7686      
# span 11 =     4.1595,     4.3976      
# span 12 =     1.5324,     2.5708      
# span 13 =     1.5325,     2.5708      
# span 14 =     0.8446,     2.3360      
# span 15 =     0.0538,     0.1134      
# span 16 =  1.8782766,  581.63464      
# span 17 =     0.0019,     0.5941      
# span 18 = 1.8334e+00, 3.1657e+02      
# span 19 =     0.8530,     2.9718      
# span 20 =      39.20,      98.51      
# span 21 =     1.9601,     4.9255      
# span 22 =    33.5324,    33.7161      
# span 23 =    33.5215,    33.6995      
# span 24 =    24.4985,    25.6694      
# span 25 =    24.4885,    25.6551      
# span 26 =    3.62709,    6.41882      
# span 27 =   59.10915,  115.16481      
# span 28 =         22,        395      
# span 29 = 0.0000e+00, 0.0000e+00      
# interval = meters: 1                  
# start_time = Jul 31 2014 21:46:25 [NMEA time, header]
# bad_flag = -9.990e-29
# <Sensors count="13" >
#   <sensor Channel="1" >
#     <!-- Frequency 0, Temperature -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>2813</SerialNumber>
#       <CalibrationDate>01-Mar-13</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.31934898e-003</G>
#       <H>6.42150445e-004</H>
#       <I>2.25157632e-005</I>
#       <J>2.11379910e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="2" >
#     <!-- Frequency 1, Conductivity -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>0492</SerialNumber>
#       <CalibrationDate>12-Feb-13</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-4.16483702e+000</G>
#         <H>4.44743188e-001</H>
#         <I>-5.16953792e-004</I>
#         <J>4.34399878e-005</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="3" >
#     <!-- Frequency 2, Pressure, Digiquartz with TC -->
#     <PressureSensor SensorID="45" >
#       <SerialNumber>1723</SerialNumber>
#       <CalibrationDate>12-Feb-13</CalibrationDate>
#       <C1>-4.620354e+004</C1>
#       <C2>-4.866022e-001</C2>
#       <C3>1.372270e-002</C3>
#       <D1>3.501600e-002</D1>
#       <D2>0.000000e+000</D2>
#       <T1>3.021120e+001</T1>
#       <T2>-4.159869e-004</T2>
#       <T3>3.603660e-006</T3>
#       <T4>4.379940e-009</T4>
#       <Slope>0.99990213</Slope>
#       <Offset>-0.94803</Offset>
#       <T5>0.000000e+000</T5>
#       <AD590M>1.146000e-002</AD590M>
#       <AD590B>-8.549020e+000</AD590B>
#     </PressureSensor>
#   </sensor>
#   <sensor Channel="4" >
#     <!-- Frequency 3, Temperature, 2 -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>0849</SerialNumber>
#       <CalibrationDate>06-Feb-13</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.85280362e-003</G>
#       <H>6.84845710e-004</H>
#       <I>3.07432916e-005</I>
#       <J>2.77832187e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="5" >
#     <!-- Frequency 4, Conductivity, 2 -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>0685</SerialNumber>
#       <CalibrationDate>30-Jan-13</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-3.97190273e+000</G>
#         <H>4.26113826e-001</H>
#         <I>-1.17809435e-005</I>
#         <J>2.06508655e-005</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="6" >
#     <!-- A/D voltage 0, Free -->
#   </sensor>
#   <sensor Channel="7" >
#     <!-- A/D voltage 1, Transmissometer, Chelsea/Seatech -->
#     <TransChelseaSeatechWetlabCStarSensor SensorID="59" >
#       <SerialNumber>CST-499</SerialNumber>
#       <CalibrationDate>25-Feb-11</CalibrationDate>
#       <M>20.1312</M>
#       <B>-1.2079</B>
#       <PathLength>0.250</PathLength>
#     </TransChelseaSeatechWetlabCStarSensor>
#   </sensor>
#   <sensor Channel="8" >
#     <!-- A/D voltage 2, Oxygen, SBE 43 -->
#     <OxygenSensor SensorID="38" >
#       <SerialNumber>0361</SerialNumber>
#       <CalibrationDate>05-Jan-14</CalibrationDate>
#       <Use2007Equation>1</Use2007Equation>
#       <CalibrationCoefficients equation="0" >
#         <!-- Coefficients for Owens-Millard equation. -->
#         <Boc>0.0000</Boc>
#         <Soc>0.0000e+000</Soc>
#         <offset>0.0000</offset>
#         <Pcor>0.00e+000</Pcor>
#         <Tcor>0.0000</Tcor>
#         <Tau>0.0</Tau>
#       </CalibrationCoefficients>
#       <CalibrationCoefficients equation="1" >
#         <!-- Coefficients for Sea-Bird equation - SBE calibration in 2007 and later. -->
#         <Soc>5.6598e-001</Soc>
#         <offset>-0.4848</offset>
#         <A>-3.2007e-003</A>
#         <B> 1.4642e-004</B>
#         <C>-2.6095e-006</C>
#         <D0> 2.5826e+000</D0>
#         <D1> 1.92634e-004</D1>
#         <D2>-4.64803e-002</D2>
#         <E> 3.6000e-002</E>
#         <Tau20> 1.2300</Tau20>
#         <H1>-3.3000e-002</H1>
#         <H2> 5.0000e+003</H2>
#         <H3> 1.4500e+003</H3>
#       </CalibrationCoefficients>
#     </OxygenSensor>
#   </sensor>
#   <sensor Channel="9" >
#     <!-- A/D voltage 3, Fluorometer, WET Labs ECO-AFL/FL -->
#     <FluoroWetlabECO_AFL_FL_Sensor SensorID="20" >
#       <SerialNumber>263</SerialNumber>
#       <CalibrationDate>20-jan-10</CalibrationDate>
#       <ScaleFactor>2.50000000e+001</ScaleFactor>
#       <!-- Dark output -->
#       <Vblank>0.0200</Vblank>
#     </FluoroWetlabECO_AFL_FL_Sensor>
#   </sensor>
#   <sensor Channel="10" >
#     <!-- A/D voltage 4, User Polynomial -->
#     <UserPolynomialSensor SensorID="61" >
#       <SerialNumber>7137</SerialNumber>
#       <CalibrationDate>08-Feb-10</CalibrationDate>
#       <SensorName>QCP-200</SensorName>
#       <A0>0.00020000</A0>
#       <A1>979.10000000</A1>
#       <A2>0.00000000</A2>
#       <A3>0.00000000</A3>
#     </UserPolynomialSensor>
#   </sensor>
#   <sensor Channel="11" >
#     <!-- A/D voltage 5, PAR/Irradiance, Biospherical/Licor -->
#     <PAR_BiosphericalLicorChelseaSensor SensorID="42" >
#       <SerialNumber>4252</SerialNumber>
#       <CalibrationDate>08-Feb-10</CalibrationDate>
#       <M>1.00000000</M>
#       <B>0.00000000</B>
#       <CalibrationConstant>3048780487.00000000</CalibrationConstant>
#       <Multiplier>1.00000000</Multiplier>
#       <Offset>-0.49530000</Offset>
#     </PAR_BiosphericalLicorChelseaSensor>
#   </sensor>
#   <sensor Channel="12" >
#     <!-- A/D voltage 6, Altimeter -->
#     <AltimeterSensor SensorID="0" >
#       <SerialNumber>118348</SerialNumber>
#       <CalibrationDate>01-SEPT-02</CalibrationDate>
#       <ScaleFactor>15.000</ScaleFactor>
#       <Offset>0.000</Offset>
#     </AltimeterSensor>
#   </sensor>
#   <sensor Channel="13" >
#     <!-- A/D voltage 7, Free -->
#   </sensor>
# </Sensors>
# datcnv_date = Jul 31 2014 16:19:55, 7.22.4 [datcnv_vars = 22]
# datcnv_in = c:\Data\simz2014c39.hex c:\Data\simz2014c39.XMLCON
# datcnv_skipover = 1
# datcnv_ox_hysteresis_correction = yes
# filter_date = Jul 31 2014 16:20:06, 7.22.4
# filter_in = c:\Data\simz2014c39.cnv
# filter_low_pass_tc_A = 0.030
# filter_low_pass_tc_B = 0.150
# filter_low_pass_A_vars =
# filter_low_pass_B_vars = prDM depSM
# alignctd_date = Jul 31 2014 16:20:09, 7.22.4
# alignctd_in = c:\Data\simz2014c39.cnv
# alignctd_adv = sbeox0V 5.000, v2 5.000                                                                                                                                                                                             
# celltm_date = Jul 31 2014 16:20:11, 7.22.4
# celltm_in = c:\Data\simz2014c39.cnv
# celltm_alpha = 0.0300, 0.0300
# celltm_tau = 7.0000, 7.0000
# celltm_temp_sensor_use_for_cond = primary, secondary
# loopedit_date = Jul 31 2014 16:20:13, 7.22.4
# loopedit_in = c:\Data\simz2014c39.cnv
# loopedit_minVelocity = 0.250                                                                                            
# loopedit_surfaceSoak: do not remove                                                                                     
# loopedit_excl_bad_scans = yes
# Derive_date = Jul 31 2014 16:20:16, 7.22.4 [derive_vars = 6]
# Derive_in = c:\Data\simz2014c39.cnv c:\Data\simz2014c39.XMLCON
# derive_time_window_docdt = seconds: 2
# derive_ox_tau_correction = yes
# binavg_date = Jul 31 2014 16:20:20, 7.22.4
# binavg_in = c:\Data\simz2014c39.cnv
# binavg_bintype = meters
# binavg_binsize = 1
# binavg_excl_bad_scans = no
# binavg_skipover = 0
# binavg_surface_bin = yes, min = 0.300, max = 0.500, value = 0.000
# file_type = binary
*END*
H�TC"�@@}Ԉ@�ψ@E7�A�E�A�6�A�D�A�g�BAO<?N-�@��$@��$@N�?z
�=�hD�?�H�C�1>@��B��@5!BB���Ak��Ag�@aT�B��CN�TCPtA@@@ň@���@��A��A�
�A��A�BI�>?��@�S$@[S$@ϲ�?{I�=��C�2�>�lC��6@4��B\C�@2"BGB��A%��A���@���B�BQ�TCJ��@�@��@�k�@{J�Al0�A-I�A/�A*ΥB-@?(��@�
$@�
$@oK�?��=�Cy�>�<Cݜ0@�[�B�@�&B#B=<�A�1�A���@w(�BhBR�TCv6�@�@}��@�i�@�Z�A�3�A[Y�A2�A�
�BC�D?^�@J�#@��#@�\�?�&�=o��CQ�>��C7�+@��B쿘@�%B$B7�A+�A���@���BXBT�TC�t�@�@�A�@q/�@��Aڅ�A ��A惂AD�B.\9?0��@B6#@�5#@p\�?�x�={`jC�u>�m�Bj�$@��B��@x+B� B�k�A�_�Ad��@���B�BV�TC���@�@LJ@廇@8O�A�F�A�L�A�D�A��B��A?}w�@Z�"@
�"@��?OI�=�PAC.J>3��B{^@�-�B��v@�/B6'B���A��Atj�@��BBX�TC��AARm�@\c�@>\�A[�A�Y�A~X�A!�Bp2?�u�@ʡ"@r�"@�@[#�=��C��$>mF�B�@���B��g@3B�(B���A���A�T�@�
�B�BZ�TC�AA)[�@+R�@�)�A�,�A'�A�)�A�L�Bӷ0?���@�x"@9x"@[N@���=���Bw
>�
�B>f@ ��BMg�@�3B�(B[�A���A�I�@���B`B\�TC�6!A AMN�@.E�@��A6�A�
�A��A�1�B]1?��@!�!@��!@�p@��=��B�O�=�.XBq@���B�R\@�4B5*Bn�A��A���@/!�BTB^�TC,V1A0A7�@�*�@��A
qA�{A�iA腨BL[/? ܇@�� @:� @��@ 9�=�P�B�+�="7Bۇ	@��|B�<J@K7B�-B|$�A��AO��@���B\B_�TCfuAA@A�І@�Ɔ@�H}A1B}AEA}A�:}A���B�.?L��@�%@@%@J�@JR�=>�B甐=-^B�@z�oB��?@�=B4B�n�A�`�A["�@�6�B�Bb�TC��QAPAZ�@��@"yA�;yA�yA�3yA���B��(?���@&�@�@�.@x��=�,_B\hi=n��A��?>�B0%P@�FBx>Be��A���A޲�@�k�BXBc�TC�aA`A(Q�@�H�@�-uA�.uA�$uA3&uA�ҪB�x!?M��@��@��@�@���=W+;Bs�C=(N�A!�?ެhB�#:@>JB�@B�h�A�Y�Ab��@�C�B<Be�TC4�qApA��@*�@��sAٴsA��sA��sA_��B�z ?
҉@�~@{~@B�?�F�=v�B*$=�7�A��?#cB��5@1LB�BBB��A���A�7�@ώ�BxBf�TCA��A�A��@��@�sA`sA�	sAusA��B��?��@�M@�M@R��?{�=���A��=�<�A|��?�I_Bz�2@LQB5GB��A���A%��@���BLBh�TC��A�A���@��@�JqAv5qAy@qA�*qAX��BA�&?��@g�@P�@���?Q�=^��APK�<�=oAW�?�[B�/@�[B'SB���A��Aj<�@V;�BpBj�TC��A�Ax��@Z��@�kA�^kA�kA�SkA\j�B2
?���@*c@$c@�[�?WY�="ɹA�M�<gkSA�x�?b
^B�1@�mB�lB���AӮ�A��@�W�BBk�TCG(�A�A���@���@��eA/�eAO�eAݙeAl�BI?���@�@�@ A�?�
�=W�A�<׼/AF��?p�aB�n4@
�B=|B�k�A
c�A��@d��B�Bm�TC�7�A�A��@&
�@�bA��bAB�bAͮbAnv�B��?&ɋ@5�@`�@��?2x�=�z�Asj�<:?A��?PbNBs%@W�BK}B���AW��A>#�@�ӿB$Bn�TC�G�A�A�|�@\��@�(`As`A]`A%`AHu�B��?=ȋ@�@@_��?��=kClA=w<�EA�'�?j�JBUD"@VsB�B���A��A�(�@��B Bp�TCdW�A�A/'�@=�@}^Adc]A��]A�V]AS��B�%?�2�@݈	@E�	@J��?&)�=��>A��G<#��@�[�?(�FB�2@l�B��B�B�A�L�A㿧@ِ�B�Br�TCg�A�A��@މ@�VA�VA��VA	�VA5իB�r?�}�@i@
@S��?h3�=-$A��+<���@�ɧ?��CB��@8�BA�BX�A��A�
�@DݪBBs�TC�v�A�Ae0}@�"}@�"PAPA�PA�PA7
�B�5?�u�@TL@M@�y�?_9�=?UAN
<~�@�t�?mj?B�!@��Ba�Bl��A���A�_�@�ĨB,Bu�TC���A�AaQ|@�C|@��MA>�MA�MAn�MA��B��?���@[@�[@д?��={��@�
<ۛ@_Z�?��:B.�@��B��By��AA��Abd�@�0�B<Bw�TCZ��A�A?�{@W�{@�
LAl�KA�KA%�KA�íB�?��@\��?J��?梮?.��=m��@�!�;)@�@�{�?�7B k@�B̑B�-�A"�A;�@0��B�Bx�TC��A�A�Bz@�0z@�HA�GA�HAr�GA)l�Bj#?t��@���?��?fK�?Vޗ=��@�B�;V<m@���?Tg3B݅@.�B!�B���A@��A�L�@�H�B�Ay�TC��A�A|y@@gy@'�EA#�EA�EA�EA�w�B�?ѕ�@���??��?�h�?�a�=1��@�;j�S@&�?�s/B�\@èB��B<��A���A�!�@���BDB|�TC���A�A&�x@�x@SfCA�kCA�VCA�\CA���B��
?Q��@�B�?�E�?8Ϟ?��=3��@���;��9@��?_+B��@0�B
�BP(�A��A�v@��}BdB}�TCy��A�AK>w@B2w@�O?A�c?A�??A�S?A@F�Bp�?Rn�@�s�?�w�?!��?{V�=Nd@b�n;? @��u?T�'B�>@��B�B���As��A!i@��nBtB��TCG��A�A��u@��u@�;Aǁ;A��;A�q;A���B�?�@K�?�O�?`��?�8y=��^@i;��@|�m?l�&B��@��B,�B��Ac
�AB"h@�olBYC��TC��BB�5u@�$u@Yp9Aq�9A�_9A�|9A�6�B(?�ʊ@/$�?�'�?56X?�K\=^k�?�j�:&��?baZ?��B���?Q�BD�B�Z�A�=�Aw�l@
�pB�A