* Sea-Bird SBE 9 Data File:
* FileName = C:\Data\simz2014c38.hex
* Software Version Seasave V 7.22.4
* Temperature SN = 2813
* Conductivity SN = 0492
* Number of Bytes Per Scan = 37
* Number of Voltage Words = 4
* Number of Scans Averaged by the Deck Unit = 1
* System UpLoad Time = Jul 31 2014 13:35:24
* NMEA Latitude = 38 18.41 N
* NMEA Longitude = 123 05.67 W
* NMEA UTC (Time) = Jul 31 2014  20:35:23
* Store Lat/Lon Data = Append to Every Scan
* SBE 11plus V 5.1g
* number of scans to average = 1
* pressure baud rate = 9600
* NMEA baud rate = 4800
* Latitude/Longitude added to scan
* GPIB address = 1
* advance primary conductivity  0.073 seconds
* advance secondary conductivity  0.073 seconds
* autorun on power up is disabled
* S>
** Project: SIMZ
** Platform: Rachel Carson
** Cruise: SIMZ2014
** Site: 38
** Cast Sequence: 38
** CTD ID: 91723
* System UTC = Jul 31 2014 20:35:24
# nquan = 30
# nvalues = 31                          
# units = specified
# name 0 = timeJ: Julian Days
# name 1 = prDM: Pressure, Digiquartz [db]
# name 2 = depSM: Depth [salt water, m]
# name 3 = c0S/m: Conductivity [S/m]
# name 4 = c1S/m: Conductivity, 2 [S/m]
# name 5 = t090C: Temperature [ITS-90, deg C]
# name 6 = t190C: Temperature, 2 [ITS-90, deg C]
# name 7 = potemp090C: Potential Temperature [ITS-90, deg C]
# name 8 = potemp190C: Potential Temperature, 2 [ITS-90, deg C]
# name 9 = xmiss: Beam Transmission, Chelsea/Seatech [%]
# name 10 = bat: Beam Attenuation, Chelsea/Seatech [1/m]
# name 11 = v1: Voltage 1
# name 12 = sbeox0V: Oxygen raw, SBE 43 [V]
# name 13 = v2: Voltage 2
# name 14 = flECO-AFL: Fluorescence, WET Labs ECO-AFL/FL [mg/m^3]
# name 15 = v3: Voltage 3
# name 16 = upoly0: Upoly 0, QCP-200
# name 17 = v4: Voltage 4
# name 18 = par: PAR/Irradiance, Biospherical/Licor
# name 19 = v5: Voltage 5
# name 20 = altM: Altimeter [m]
# name 21 = v6: Voltage 6
# name 22 = sal00: Salinity, Practical [PSU]
# name 23 = sal11: Salinity, Practical, 2 [PSU]
# name 24 = sigma-�00: Density [sigma-theta, Kg/m^3]
# name 25 = sigma-�11: Density, 2 [sigma-theta, Kg/m^3]
# name 26 = sbeox0ML/L: Oxygen, SBE 43 [ml/l], WS = 2
# name 27 = sbeox0PS: Oxygen, SBE 43 [% saturation], WS = 2
# name 28 = nbin: number of scans per bin
# name 29 = flag: flag
# span 0 = 212.858014, 212.863482       
# span 1 =      2.015,     32.245       
# span 2 =      2.000,     32.000       
# span 3 =   3.890242,   4.299201       
# span 4 =   3.897770,   4.296424       
# span 5 =    12.2587,    16.7936       
# span 6 =    12.3546,    16.7758       
# span 7 =    12.2545,    16.7933       
# span 8 =    12.3504,    16.7755       
# span 9 =    74.4184,    86.7826       
# span 10 =     0.5670,     1.1819      
# span 11 =     3.7567,     4.3709      
# span 12 =     1.7002,     2.7274      
# span 13 =     1.7002,     2.7273      
# span 14 =     1.3305,     6.0816      
# span 15 =     0.0732,     0.2633      
# span 16 = -0.0468565,  524.17581      
# span 17 =    -0.0000,     0.5354      
# span 18 = 5.1952e-01, 4.0130e+02      
# span 19 =     0.4918,     3.0569      
# span 20 =      23.65,      51.03      
# span 21 =     1.1827,     2.5513      
# span 22 =    33.5112,    33.6836      
# span 23 =    33.5018,    33.6698      
# span 24 =    24.4211,    25.5188      
# span 25 =    24.4182,    25.4893      
# span 26 =    4.14473,    6.91276      
# span 27 =   68.28349,  124.05582      
# span 28 =         19,        475      
# span 29 = 0.0000e+00, 0.0000e+00      
# interval = meters: 1                  
# start_time = Jul 31 2014 20:35:23 [NMEA time, header]
# bad_flag = -9.990e-29
# <Sensors count="13" >
#   <sensor Channel="1" >
#     <!-- Frequency 0, Temperature -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>2813</SerialNumber>
#       <CalibrationDate>01-Mar-13</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.31934898e-003</G>
#       <H>6.42150445e-004</H>
#       <I>2.25157632e-005</I>
#       <J>2.11379910e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="2" >
#     <!-- Frequency 1, Conductivity -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>0492</SerialNumber>
#       <CalibrationDate>12-Feb-13</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-4.16483702e+000</G>
#         <H>4.44743188e-001</H>
#         <I>-5.16953792e-004</I>
#         <J>4.34399878e-005</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="3" >
#     <!-- Frequency 2, Pressure, Digiquartz with TC -->
#     <PressureSensor SensorID="45" >
#       <SerialNumber>1723</SerialNumber>
#       <CalibrationDate>12-Feb-13</CalibrationDate>
#       <C1>-4.620354e+004</C1>
#       <C2>-4.866022e-001</C2>
#       <C3>1.372270e-002</C3>
#       <D1>3.501600e-002</D1>
#       <D2>0.000000e+000</D2>
#       <T1>3.021120e+001</T1>
#       <T2>-4.159869e-004</T2>
#       <T3>3.603660e-006</T3>
#       <T4>4.379940e-009</T4>
#       <Slope>0.99990213</Slope>
#       <Offset>-0.94803</Offset>
#       <T5>0.000000e+000</T5>
#       <AD590M>1.146000e-002</AD590M>
#       <AD590B>-8.549020e+000</AD590B>
#     </PressureSensor>
#   </sensor>
#   <sensor Channel="4" >
#     <!-- Frequency 3, Temperature, 2 -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>0849</SerialNumber>
#       <CalibrationDate>06-Feb-13</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.85280362e-003</G>
#       <H>6.84845710e-004</H>
#       <I>3.07432916e-005</I>
#       <J>2.77832187e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="5" >
#     <!-- Frequency 4, Conductivity, 2 -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>0685</SerialNumber>
#       <CalibrationDate>30-Jan-13</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-3.97190273e+000</G>
#         <H>4.26113826e-001</H>
#         <I>-1.17809435e-005</I>
#         <J>2.06508655e-005</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="6" >
#     <!-- A/D voltage 0, Free -->
#   </sensor>
#   <sensor Channel="7" >
#     <!-- A/D voltage 1, Transmissometer, Chelsea/Seatech -->
#     <TransChelseaSeatechWetlabCStarSensor SensorID="59" >
#       <SerialNumber>CST-499</SerialNumber>
#       <CalibrationDate>25-Feb-11</CalibrationDate>
#       <M>20.1312</M>
#       <B>-1.2079</B>
#       <PathLength>0.250</PathLength>
#     </TransChelseaSeatechWetlabCStarSensor>
#   </sensor>
#   <sensor Channel="8" >
#     <!-- A/D voltage 2, Oxygen, SBE 43 -->
#     <OxygenSensor SensorID="38" >
#       <SerialNumber>0361</SerialNumber>
#       <CalibrationDate>05-Jan-14</CalibrationDate>
#       <Use2007Equation>1</Use2007Equation>
#       <CalibrationCoefficients equation="0" >
#         <!-- Coefficients for Owens-Millard equation. -->
#         <Boc>0.0000</Boc>
#         <Soc>0.0000e+000</Soc>
#         <offset>0.0000</offset>
#         <Pcor>0.00e+000</Pcor>
#         <Tcor>0.0000</Tcor>
#         <Tau>0.0</Tau>
#       </CalibrationCoefficients>
#       <CalibrationCoefficients equation="1" >
#         <!-- Coefficients for Sea-Bird equation - SBE calibration in 2007 and later. -->
#         <Soc>5.6598e-001</Soc>
#         <offset>-0.4848</offset>
#         <A>-3.2007e-003</A>
#         <B> 1.4642e-004</B>
#         <C>-2.6095e-006</C>
#         <D0> 2.5826e+000</D0>
#         <D1> 1.92634e-004</D1>
#         <D2>-4.64803e-002</D2>
#         <E> 3.6000e-002</E>
#         <Tau20> 1.2300</Tau20>
#         <H1>-3.3000e-002</H1>
#         <H2> 5.0000e+003</H2>
#         <H3> 1.4500e+003</H3>
#       </CalibrationCoefficients>
#     </OxygenSensor>
#   </sensor>
#   <sensor Channel="9" >
#     <!-- A/D voltage 3, Fluorometer, WET Labs ECO-AFL/FL -->
#     <FluoroWetlabECO_AFL_FL_Sensor SensorID="20" >
#       <SerialNumber>263</SerialNumber>
#       <CalibrationDate>20-jan-10</CalibrationDate>
#       <ScaleFactor>2.50000000e+001</ScaleFactor>
#       <!-- Dark output -->
#       <Vblank>0.0200</Vblank>
#     </FluoroWetlabECO_AFL_FL_Sensor>
#   </sensor>
#   <sensor Channel="10" >
#     <!-- A/D voltage 4, User Polynomial -->
#     <UserPolynomialSensor SensorID="61" >
#       <SerialNumber>7137</SerialNumber>
#       <CalibrationDate>08-Feb-10</CalibrationDate>
#       <SensorName>QCP-200</SensorName>
#       <A0>0.00020000</A0>
#       <A1>979.10000000</A1>
#       <A2>0.00000000</A2>
#       <A3>0.00000000</A3>
#     </UserPolynomialSensor>
#   </sensor>
#   <sensor Channel="11" >
#     <!-- A/D voltage 5, PAR/Irradiance, Biospherical/Licor -->
#     <PAR_BiosphericalLicorChelseaSensor SensorID="42" >
#       <SerialNumber>4252</SerialNumber>
#       <CalibrationDate>08-Feb-10</CalibrationDate>
#       <M>1.00000000</M>
#       <B>0.00000000</B>
#       <CalibrationConstant>3048780487.00000000</CalibrationConstant>
#       <Multiplier>1.00000000</Multiplier>
#       <Offset>-0.49530000</Offset>
#     </PAR_BiosphericalLicorChelseaSensor>
#   </sensor>
#   <sensor Channel="12" >
#     <!-- A/D voltage 6, Altimeter -->
#     <AltimeterSensor SensorID="0" >
#       <SerialNumber>118348</SerialNumber>
#       <CalibrationDate>01-SEPT-02</CalibrationDate>
#       <ScaleFactor>15.000</ScaleFactor>
#       <Offset>0.000</Offset>
#     </AltimeterSensor>
#   </sensor>
#   <sensor Channel="13" >
#     <!-- A/D voltage 7, Free -->
#   </sensor>
# </Sensors>
# datcnv_date = Jul 31 2014 16:19:18, 7.22.4 [datcnv_vars = 22]
# datcnv_in = c:\Data\simz2014c38.hex c:\Data\simz2014c38.XMLCON
# datcnv_skipover = 1
# datcnv_ox_hysteresis_correction = yes
# filter_date = Jul 31 2014 16:19:30, 7.22.4
# filter_in = c:\Data\simz2014c38.cnv
# filter_low_pass_tc_A = 0.030
# filter_low_pass_tc_B = 0.150
# filter_low_pass_A_vars =
# filter_low_pass_B_vars = prDM depSM
# alignctd_date = Jul 31 2014 16:19:32, 7.22.4
# alignctd_in = c:\Data\simz2014c38.cnv
# alignctd_adv = sbeox0V 5.000, v2 5.000                                                                                                                                                                                             
# celltm_date = Jul 31 2014 16:19:34, 7.22.4
# celltm_in = c:\Data\simz2014c38.cnv
# celltm_alpha = 0.0300, 0.0300
# celltm_tau = 7.0000, 7.0000
# celltm_temp_sensor_use_for_cond = primary, secondary
# loopedit_date = Jul 31 2014 16:19:36, 7.22.4
# loopedit_in = c:\Data\simz2014c38.cnv
# loopedit_minVelocity = 0.250                                                                                            
# loopedit_surfaceSoak: do not remove                                                                                     
# loopedit_excl_bad_scans = yes
# Derive_date = Jul 31 2014 16:19:39, 7.22.4 [derive_vars = 6]
# Derive_in = c:\Data\simz2014c38.cnv c:\Data\simz2014c38.XMLCON
# derive_time_window_docdt = seconds: 2
# derive_ox_tau_correction = yes
# binavg_date = Jul 31 2014 16:19:43, 7.22.4
# binavg_in = c:\Data\simz2014c38.cnv
# binavg_bintype = meters
# binavg_binsize = 1
# binavg_excl_bad_scans = no
# binavg_skipover = 0
# binavg_surface_bin = yes, min = 0.300, max = 0.500, value = 0.000
# file_type = binary
*END*
��TC �@@��@M|�@ZY�A�4�A�X�A'4�A�E�B}��?�Lt@P}-@�|-@,��?�=AD�
	?N��C�C@LB�H#@�B/B~^�AcX�Ax��@��B.C��TCNtA@@@u�@s�@*�A��A-�A��APW�B�#�?o�r@%8.@�7.@pq@]��=���C�]�>�.xC��6@�LHB}= @tB�
B	��AY��A��@�/�B�B��TCG��@�@҈@�Lj@�[�ApY�AFZ�A X�A5F�B�ƕ?Pq@+�.@��.@d
@�J�=ί�CX��>�~3CM/@ƠEB8@{B�B���A>��AP5�@��B�A��TCr6�@�@}��@���@���A~��A
��Aړ�A*��B���?ˬp@�.@��.@��'@���=�p�C�T�>!IC��(@tABK�@6BVB5�Ab�A���@T�B�A��TC�t�@�@���@�u�@�t�A�p�A�r�A�n�A8֔B�G�?Mmp@}�-@	�-@b
b@I'%>PAC�-J>�U�BI9@��<B��@qB�
B	�A��A��@��B�B��TC��@�@��@�z�@w�A�w�A�t�Aeu�A�Z�B��?&@q@�c-@Xc-@��a@C�$>�xC�j>�ީB�@Yd9BGP@�B�
B�A5�AU�@D3�B�A��TC��AA��@t~�@[y�A!{�A�v�A�x�A̒�B���?�q@�,@��,@S�m@��,>���Bӫ�=��hB
~@'C5B�@�B�BG�A�
�A�2�@�:�B�B��TC�AA���@~�@�w�AFy�A
u�ATv�AL-�BD��?��r@�m,@ m,@a�d@�&>зB�=�=�wNB��@f�0B�f
@BB<�A�A���@���B�A��TC�6!A A�}�@�q�@�R�A7L�A]O�A�H�A��By��?�t@��+@ �+@Q�`@�w$>���B=�=�
B�w@�,B� 
@B�B�.�AM �A��@��B�B��TC(V1A0A�e�@5]�@R�A�	�A��A*�A�x�B2��?;s@��*@��*@ʍe@�d'>�NBV.X=T��A�,�?�)B"�@�#BuB�F�A#7�A��@���B�A��TCauAA@A�'�@�@wQ�A�F�A�M�A�B�A�J�B��?�Tt@MR*@�Q*@+�z@�
5>��(BWe0=���A���?%i&B� @�+BX"B�}�A�q�A?Y�@�D�B�A��TC��QAPA�‡@:��@�Y�AJ�AyU�A�E�A��Bؒ�?Inu@U�(@��(@
��@:\H>QOBc`
=y�AOi�?�P!BD

@�$B�#Bi��A���A[0�@AJ�B�B��TC�aA`A;w�@�o�@,x�A�|�A�s�Apx�A�%�Bu�?�tz@�q&@_q&@g��@��J>?�A�a�<�mA9��?\�B���?�/Bh%B���A���A(��@ʵ�B�A��TC.�qApAj�@G`�@Y�ABX�A=T�AmS�Ap��B���?�y@�%@��%@4�@/V>�j�A�ܩ<��EA��?�QB���?�-B�#B!��AG��A͇�@�o�B�A��TC>��A�Aj!�@�@"Ab�~A�A"�~A��B��~?@�{@y� @S� @"��@Sʆ>( yA�E�<yA�?��B]l�?�1B�)BI'�AC!�A���@:n�B�B��TC��A�A���@���@5�{AL�{Ah�{A�{A�B�Q?퉃@��@��@�,�@8�O>g7A h?<	�@��?3�B��??B>6B[��A׋�Aξ@���B�A��TC��A�A�n�@Pd�@YyuA#vuAnuA�juA�æB{!:?gv�@$�@7�@V1@k�>�A-
<�X�@��?Ɍ
B�z�?�YB�NB�x�A�g�A�@�A�BB��TCC(�A�A�m�@�^�@�	pA��oA�oA"�oA��B�%?��@��@��@99@�=/��@�3<���@mߚ?Ny	BI��?�aB�ZB��A��Aа�@7��B�B��TC�7�A�A��@=�@�[mA/amA�OmA�TmA���Bn� ?OΉ@�@E�@B4�?���==�@ye�;
m@��?ڌB*��?�jB�aB:u�Ang�A�ý@T��BhB��TC�G�A�AT��@>��@]3lA�blA�&lAVlA���B͛ ?�͉@�@7�@��@���= 2�@U}�;��M@�ֆ?��BV��?�pBefB���A���Aeʼ@Ў�BB��TC`W�A�A���@���@�3kA=kAi&kA�/kA=q�B��#?�b�@G@KG@n�
@0q�=Y�@Lӝ;s
7@�=�?�%B�o�?�sB�jB��A���A
��@�3�BB��TCg�A�A�x�@sm�@��jAq�jAċjA�~jA�Z�B`i*?B��@��@�@��!@պ�=d�Y@��c;+@{Gp?�XB:��?�uB�kBL��A]��A��@���B�B��TC�v�A�A�}�@3m�@�;eA~�dA�-eA:�dA2��BV.?�	�@�.@�/@��/@V�>g@U;I:�?�`?'r�AS[�?FBAzB�r�A�q�A���@Y��B�A��TC���A�A��@��@X�\Aó\Aغ\AD�\A@R�B��6?��@�@o @�9H@�>&
@�;���?o�W?ak�AM��?��B�Bta�A2^�A߇�@3L�B�A��TCU��A�A�5�@;2�@&�XA�XA@�XA%�XA��B�h.?��@In@o@��-@��>�
�?��:"J�?�L?���A2��?��BG�B7��A���A%&�@l3�B�A��TC��A�A6��@�F�@l�ZArYAޣZA��XA뚧B��4?\!�@6��?���?��@�M�=���?C��:�P�?Δ6?���A��?h�BИB���A���A��@?��BB��TCߵ�A�A�?|@J|@��MA[�LAHMA��LA��B/U ?�׉@2+�?1.�?k�	@tr�=�?

�:`�?�,?���A���B��B��A�(�AX��@��B�A��TC���A�A�|@iy{@�MAoKA��LA+_KA�0�B�M?���@��?%��?�%�?Y"�=c,�?��:�~h?�!?���Ap��?�B_�B-�Ai<�Am�@��B�B��TCs��A�A��z@��z@ChIAU�HA�WIA�HA���B?�E�@6�?�
�?!�?���=��S?Ӥ]:��C?��?���A^—?�B��Bt�A���A��@��B$B��TCA��A�A��{@]z@YKA�;HAHKA�*HA�f�B?\�@��?
�?���?\�=��>j~:d-?�
?_<�A�c�?өB��B�V�A���Af"�@-��B��C
�TC��BB��x@uy@�#DAf�EAsDA+�EA���B3(?ދ@��?H��?�M�?@��=��?��I��?��>�(�A� �?��BӭB�&�A(��A���@&��B�C